|
|
 4lo in reverse
#1003796
07/21/10 09:33 AM
|
Joined: May 2009
Posts: 56
OP
Getting the Wheeling Fever
|
Hello, my 87 w/manual trans wont stay in 4lo if i shift it in reverse, it pull the shifter out of gear, is this normal or is something wrong? Thanks Mike
|
|
|
Re: 4lo in reverse
[Re: 87Raider]
#1003797
07/21/10 02:49 PM
|
Joined: Dec 2004
Posts: 314
Mudrunner
|
Do you have autohubs? I wonder if this could be your problem? I'll let others more knowledgeable speak up.
'88 Raider 2.6L - SW Hubs, Weber 32/36, Off-road Pkg - Dead
'88 Monty 2.7L - 5" Lift, Weber 38, 33's, Dual Fans, Dual bouncy (more goodies to install) - Still Kicking.
'03 Monty Sport - XLS, BFG A/T's - Dead
|
|
|
Re: 4lo in reverse
[Re: 87Raider]
#1003798
07/21/10 03:09 PM
|
Joined: Nov 2003
Posts: 5,690
Trail Leader
|
Which shifter? The Transmission or the transfer case?
1999 Mitsu Montero - Crappy Weather
1992 Isuzu Pickup - Zombie Apocalypse
2008 Saturn Sky Redline - Nice Weather
|
|
|
Re: 4lo in reverse
[Re: 87Montero]
#1003799
07/21/10 04:31 PM
|
Joined: Dec 2008
Posts: 659
Rock Warrior
|
Sounds like tcase to me. either way, it is not normal. have you installed a body lift? I would check to see if there is anything getting in the tcase shifters way that is preventing it from fully locking in or is putting tenstion on it when in 4lo making it easier to slip out of gear. Since it is only happening in R, your running gear should be torqueing in the opposite direction, so maybe something is binding?
'88 Raider. 2.6L dead...2.4L swap in progress, AT, 33's, 2 bouncy seat,AC, CC, 2.25 exh, 2" Tbar, 2" BL, rear DB, rear LSD,4.90's, SW hubs,gen2 uca's, KYB shocks, snorkel, elec fan, MSD.
'99 chev k3500 crewcab
'15 Subaru XV
'03 BMW i325
|
|
|
Re: 4lo in reverse
[Re: zarktheshark]
#1003800
07/21/10 06:48 PM
|
Joined: Apr 2006
Posts: 1,193
Body Damage is Cool
|
|
it dosent have to be surrounded by water to be an island
|
|
|
Re: 4lo in reverse
[Re: 87Raider]
#1003801
07/21/10 11:55 PM
|
Joined: Dec 2006
Posts: 74
Getting the Wheeling Fever
|
It has been a while, but I had the same problem. There is a roll pin at the bottom of the tranny shifter that is pushed to far one way or the other. I used a pair of channel locks to even it up. I don't remember all the details. I'm sure someone here can help you out. <img src="/forums/images/graemlins/kewl.gif" alt="" />
1988 Dodge Raider, Clearwater, 33x12.5 Buckshots, RB 2" Lift, Weber, 2.6L rebuilt by me with a lot of help from you guys. Thanks! www.cardomain.com/ride/2980730
|
|
|
Re: 4lo in reverse
[Re: mxmikie]
#1003802
07/22/10 02:41 AM
|
Joined: May 2009
Posts: 56
OP
Getting the Wheeling Fever
|
It pulls the tranfer case shifter out of 4lo, also the trans mount is brand new. I'll open the top and check the roll pin, Thanks for all the help. Mike
|
|
|
Re: 4lo in reverse
[Re: 87Raider]
#1003803
07/22/10 03:05 PM
|
Joined: Jun 2003
Posts: 7,356
Trail Leader
|
What about the body lift question? If you have lifted it, putting the tranny shifter in R might pull the tcase shifter back from the stretching of the boots. (?)
Big Truck: 00, 3.5, Endeavor, 5-Spd drive line in hand! Little Truck: 87, 2.6T I/C, MT, LSDs, Tonneau Top Her Truck: 03, 3.8, 20th Anniv, 65k Daughter's: 06 Eclipse, Keeping it Mitsu! FSMs: MitsubishiLinks.com
|
|
|
Re: 4lo in reverse
[Re: MontyMcV]
#1003804
07/22/10 09:22 PM
|
Joined: May 2001
Posts: 4,079
Roll Me Over
|
It has been a while, but I had the same problem. There is a roll pin at the bottom of the tranny shifter that is pushed to far one way or the other. I used a pair of channel locks to even it up. I don't remember all the details. I'm sure someone here can help you out. Correct the pin in the shifter rod that runs thru the transfer case is to far in or not enough
89 2 dr turbo diesel
89/88 "Backwoods sas"
|
|
|
Re: 4lo in reverse
[Re: lordtrunks]
#1003805
07/27/10 06:12 AM
|
Joined: May 2009
Posts: 56
OP
Getting the Wheeling Fever
|
Hello, the truck is not lifted, also I noticed that in will pull out of 4lo if I try to put it into 4th too,, Is the pin your talking about accessible from the top of the Transfer case? Also Is the pin on the transfer case shifter? Thank You For your Help..Mike
|
|
|
|
