Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
FCC ID for 96 SR Needed #1047764 06/06/12 11:15 PM
Joined: May 2012
Posts: 51
M
Monster Offline OP
Getting the Wheeling Fever
I ordered a keyfob off of ebay, could not get it to pair with my trucks keyless control module next to the rear right speaker. Seller claims there are three type of them ,and the key fob they have sent was tested and works good.
Can anybody with a 96SR post a picture and/or FCC ID # on their factory keyfob here?

Thanks! <img src="/forums/images/graemlins/cheers.gif" alt="" />

Re: FCC ID for 96 SR Needed [Re: Monster] #1047765 06/07/12 01:50 AM
Joined: Apr 2006
Posts: 1,193
mxmikie Offline
Body Damage is Cool


it dosent have to be surrounded by water to be an island
Re: FCC ID for 96 SR Needed [Re: Monster] #1047766 06/13/12 07:06 PM
Joined: Jun 2004
Posts: 1,513
S
sasnydley Offline
Body Damage is Cool
I have 95 sr. and apparently it has aftermarket dealer installed module on it...? The original fob has mitsu sign on it and is falling apart. I got several fobs I ordered online- None of them worked. I was told to go to local car electronics shop or key smith which will cost more and haven't done it yet.It may be that the 96 has same issue.


1990 Black Monty LS Over 300K' 1993 Isuzu Rodeo LS 4x4 46k (yes only 46K!)1989 Honda Transalp 600 Africa twin,
Re: FCC ID for 96 SR Needed [Re: sasnydley] #1047767 06/18/12 11:36 PM
Joined: May 2012
Posts: 51
M
Monster Offline OP
Getting the Wheeling Fever
Quote
I have 95 sr. and apparently it has aftermarket dealer installed module on it...? The original fob has mitsu sign on it and is falling apart. I got several fobs I ordered online- None of them worked. I was told to go to local car electronics shop or key smith which will cost more and haven't done it yet.It may be that the 96 has same issue.


Yea, if it comes to Mitsu dealer they will charge upwards of $100, with that I can get a really nice after market with engine start for those freezing winter days. <img src="/forums/images/graemlins/cheers.gif" alt="" />

Re: FCC ID for 96 SR Needed [Re: Monster] #1047768 06/19/12 12:33 AM
Joined: Jan 2000
Posts: 16,227
off-roader Offline
Web Wheeler
*****
Grasscat replaced the OE fob on his with an ebay unit. IIRC the receiver module which I believe has the FCC ID is slightly above and behind the passenger wheel well but check the FSM before you start removing body panels.


Off Roader
98 Montero with the Winter Package
89 Montero minty clean and reserved for overlanding trips or Cars and Coffee events
96SR (3.15:1 xcase, 35's) gone to the rust gods
96SR Build Up Thread
Old web page
Old web page
Re: FCC ID for 96 SR Needed [Re: off-roader] #1047769 06/19/12 02:48 AM
Joined: May 2012
Posts: 51
M
Monster Offline OP
Getting the Wheeling Fever
Quote
Grasscat replaced the OE fob on his with an ebay unit. IIRC the receiver module which I believe has the FCC ID is slightly above and behind the passenger wheel well but check the FSM before you start removing body panels.


I went through that <img src="/forums/images/graemlins/smile.gif" alt="" /> in fact the panel is still not put back together, the fob just doesn't seem to register with the car unit. I went through this whole thing with the ebay seller, they claimed the unit has been tested... AND apparently there are two types of fobs.
I dont know if the keyless entry units in the Montys go bad, but I think it would be safer to just spend the money on an after market system. <img src="/forums/images/graemlins/cheers.gif" alt="" />








4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 0.014s Queries: 15 (0.003s) Memory: 0.6106 MB (Peak: 0.6809 MB) Data Comp: Off Server Time: 2026-06-17 16:04:02 UTC
Valid HTML 5 and Valid CSS