Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Page 2 of 2 1 2
Re: Bad Intake Manifold Gasket... [Re: glock] #390958 02/03/04 01:35 AM
Joined: Mar 2001
Posts: 358
C
central Offline
Mudrunner
Isuzu appears to be fairly reasonable when it comes to the IMGs. They seem to recognize their snafu and are willing to do the right thing (e.g. the previously mentioned doing the work after the warranty period for some folks).

Surely your dealer will know that if one gasket of the same material and design fails the other cannot be far behind. This is all the more true since this is a widespread COMMON problem. If they are at all service oriented they should just do it without you even asking. If they aren't planning to, then ask and point out the upcoming need and obvious cost savings of doing it now rather than later. If that doesn't work call Isuzu and tell them what is going on and see if they don't agree that it will save them money to pay for both jobs at once rather than one at a time. Like I said, based on other posts IMGs seems to be a case where they will do the right thing. In any event I don't see what it can hurt to at least ask.

Re: Bad Intake Manifold Gasket... [Re: central] #390959 02/04/04 02:35 PM
Joined: Feb 2002
Posts: 163
glock Offline OP
Wheeler
Thanks for the input and support guys...as always. <img src="/forums/images/graemlins/cheers.gif" alt="" />

Picked the Troop up last night...They did the job and did it right- all gaskets replaced. Also did the recall fuel line/shield that needed to be done.

The idle seems to have been set a liiittle low- stalled 2x when putting into park, so I am calling them to make a note- but I should be able to handle that as soon as I get my hands on a 2000 service manual!! <img src="/forums/images/graemlins/angry.gif" alt="" />

...unless someone feeling creative cares to hook me up here somehow...?? <img src="/forums/images/graemlins/notooth.gif" alt="" />


2012 Jeep Liberty

2000 Trooper 3.5, LS/Burgandy & Grey(O.B.T.2)...<img src="/forums/images/graemlins/cheers.gif" alt="" />

I WAS down with O.B.T. '88 Trooper II
("Old Blue Trooper!" said my kids!...)
Re: Bad Intake Manifold Gasket... [Re: glock] #390960 02/04/04 03:47 PM
Joined: May 2002
Posts: 1,863
rubo Offline
Body Damage is Cool
You can't adjust the idle on our trucks.
It's computer controled.
You might need to check some of the sensors connected with idle, to see if they are working properly.

Sorry can't help you more on this, i'm not very good with ellectronicaly controled engines <img src="/forums/images/graemlins/baby.gif" alt="" />.


"If i can't crawl over it, i'll fly over it"
rubo

'96 Amigo 4x4, 3.2L V6, 4L30E, D44 rear, SOA, 1" BL, undergoing surgery.
'00 Rodeo LS 4x4, 3.2L V6, OME 919 Springs, front cranked to match,1" BL, 265/70x16 Scorion A/T's.
Re: Bad Intake Manifold Gasket... [Re: rubo] #390961 02/05/04 10:46 PM
Joined: Feb 2002
Posts: 163
glock Offline OP
Wheeler
Quote
You can't adjust the idle on our trucks.
It's computer controled...


.....aaaagghhhh!!...... <img src="/forums/images/graemlins/angry.gif" alt="" />


2012 Jeep Liberty

2000 Trooper 3.5, LS/Burgandy & Grey(O.B.T.2)...<img src="/forums/images/graemlins/cheers.gif" alt="" />

I WAS down with O.B.T. '88 Trooper II
("Old Blue Trooper!" said my kids!...)
Re: Bad Intake Manifold Gasket... [Re: glock] #390962 02/06/04 06:13 AM
Joined: Mar 2001
Posts: 248
TLB Offline
Wheeler
Beem away for a bit, I'm glad to see the job got taken care of under warranty <img src="/forums/images/graemlins/kewl.gif" alt="" /> Take it easy!

Tim
99 Rodeo


Tim Barlow
05' Sequoia SR5
98' 4Runner SR5
Page 2 of 2 1 2







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 0.006s Queries: 15 (0.004s) Memory: 0.6146 MB (Peak: 0.6798 MB) Data Comp: Off Server Time: 2026-06-07 11:26:02 UTC
Valid HTML 5 and Valid CSS