Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Make your own fender flares? #397685 02/11/04 12:15 PM
Joined: Nov 2003
Posts: 452
CDUFF7 Offline OP
Mudrunner
Has anyone ever done this? I saw a Jeep Cherokee (built) here in Japan that had what looked like some very good home made rubber fender flares to cover the wide tires.
I was curious if anyone has done something similar and could lend some advice on materials or how-to's?

Thank you,

Chris

Re: Make your own fender flares? [Re: CDUFF7] #397686 02/11/04 06:57 PM
Anonymous
Unregistered
For awhile, I had vinyl base (bought from Home Depot, used where floor meets wall or meets base cabinets) screwed into my wheelwells. Not particularly attractive, but not horrible looking either.

Kept me legal and kept mud and spray from getting up on things. The home stores have 4 inch base, but you can also get 6 inch through some distributors.

Re: Make your own fender flares? [Re: CDUFF7] #397687 02/11/04 07:53 PM
Anonymous
Unregistered
Don't mean to hijack Chris, but have you seen these flares over there?


[Linked Image]


I've been looking for a while. Check my earlier post. They have the look of a factory option. <img src="/forums/images/graemlins/kewl.gif" alt="" /> And there's no bolts on the outside like a bushwacker. If you do have a source how does a person here in the states get ahold of a set? I also like the driving lights on the Surfs do you have a source for those over there? Sorry for the hijack <img src="/forums/images/graemlins/ignore.gif" alt="" />

Re: Make your own fender flares? [Re: CDUFF7] #397688 02/11/04 08:55 PM
Joined: Dec 2000
Posts: 882
M
missouriman Offline
Rock Warrior
look in the garden section of local lowes or something like that, that is what I will go with in the spring. garden edgeing. has a rounded (outer) edge and a lip to seal it up a bit. or I am going to say fawk it and saws all the fenders to fit 40s move the rear back 4 inchs and the front forward 3 to 4 inches. turn on the heater or air and cruise the hills

Re: Make your own fender flares? [Re: missouriman] #397689 02/11/04 10:32 PM
Anonymous
Unregistered
i'm cutting mine this weekend to fit some 35's better.. i'm planning on cutting anywhere from 2-4 inches per fender, we'll see how well my first cut goes! and then from there grind them down.. after that i'll take a piece of tube about 1mm think and tack weld it up there.. then fill in the gap between the sheetmetal and tube with something (not sure yet) to create a lip.. then i'm going to take some form of bed liner and paint over the tube and about .5in of the cut. so i'll have lips with bed liner on them...

Re: Make your own fender flares? #397690 02/11/04 11:14 PM
Joined: Apr 2002
Posts: 5,688
Esquire812 Offline
Trail Leader
Quote
so i'll have lips with bed liner on them...


Just be careful you dont get any of that bed liner stuff on your hootus...takes forever for it to wear off! Lips wouldnt be so bad...ever seen Police Academy? Hehehe

~Darin <img src="/forums/images/graemlins/baby.gif" alt="" />


88' 4x4 *22R-EB Gen II*
87' $Runner *22R-EB Gen I*
85' Sillyca 22R-Esq

"I LIVE IN MY OWN WORLD...THEY KNOW ME WELL THERE"
Re: Make your own fender flares? [Re: Esquire812] #397691 02/11/04 11:56 PM
Joined: Nov 2003
Posts: 79
jvmin Offline
Getting the Wheeling Fever
I saw a post once, and can't find it to save my life.
It was where the guy took his sawzall, and cut into his existing fender wells, not cutting them out but cutting slits in them. then bending the whole thing out, and filling in the gaps with some extra sheet metal.

He also rebent the lip edge of the fender further under on each section and then he glassed over the whole thing and painted it it looked great.

Itlooked like factory widened fenders. they stuck out about 4 inches and were cut back from the original opening about 3 inches or so. I wish I could find it. I want to do this to mine

Re: Make your own fender flares? #397692 02/15/04 12:56 AM
Joined: Nov 2003
Posts: 452
CDUFF7 Offline OP
Mudrunner
Thank you all for the inputs, I am going to look for some of the rubber material today. Like the Flares on the 1st gen - that truck looks like it is in Japan? In fact it looks very similar to mine (check sig) - I have seen those flares before but not on 1st gen Surfs.

Re: Make your own fender flares? [Re: CDUFF7] #397693 02/15/04 07:15 AM
Anonymous
Unregistered
Dang that's a nice look'n ride! Send me some of those chrome mirrors and a bull bar! <img src="/forums/images/graemlins/smile.gif" alt="" /> <img src="/forums/images/graemlins/kewl.gif" alt="" />

shaggy

Re: Make your own fender flares? #397694 02/15/04 11:42 AM
Joined: Nov 2003
Posts: 452
CDUFF7 Offline OP
Mudrunner
Thanks Shaggy - that is a standard set of Mirrors and the stock bull bar - I did repaint the bull bar - it used to be black with some rust. I wish I could send stuff like that to the states but it is heavy - the mirrors I would send but can not find any old runners (surfs) in the junk yards.


Moderated by  4Crawler, 4x4Wire, kewlynx 







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 5.545s Queries: 15 (0.005s) Memory: 0.6229 MB (Peak: 0.7306 MB) Data Comp: Off Server Time: 2026-11-16 01:27:53 UTC
Valid HTML 5 and Valid CSS