Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Page 2 of 2 1 2
Re: winch installation [Re: Gellekanao] #407713 02/28/04 03:43 AM
Joined: Sep 2002
Posts: 3,634
bretwalda Offline
Roll Me Over
Alex Kogan on this board did a spectactular setup for his Gen2.

I havent seen any update on this but it sounds like using the stock bumper was possible with this configuration


concreteprinter.com
Re: winch installation [Re: Lloyd Swartz] #407714 02/28/04 04:06 AM
Joined: Oct 2003
Posts: 1,258
DavidG Offline
Body Damage is Cool
Rob, you raise very good points and I absolutely agree with the safety issues. I can honestly say that right now I don't need one, but after getting previous rigs stuck, I now I would like a winch in the future. My greatest concern is altering the airbag deployment.

I've seen ARB bumpers build specifically to handle proper deployment, and that's what I'm after. Unfortunately, it appears an airbag-compatible bumper is not available. I would rather get stuck without a winch than fool around with the impact sensors and endanger my family. Besides, this thing is only driven offroad maybe 5% of the time and I'm much more likely running into another vehicle driving to work. Still, I wish I could find the right application.

Do you guys think a 4-5k class 3 hitch would hold up to the potential 8-9k lb pull of a receiver mounted winch? Oh, and Lloyd, thanks for the offer. The center portion of the factory bumper just begs for that sort of custom treatment!

Thanks guys,

David


1997 Montero SR

<a href="www.georgiaoverland.com" target="_blank">www.georgiaoverland.com</a>
Re: winch installation #407715 02/28/04 04:45 AM
Joined: Jun 2003
Posts: 152
Gellekanao Offline OP
Wheeler
Alternatively, Warn sells a "pull pack"...basically, a winch mounted to a trailer drawbar...plug it in your receiver, hook cables up to your battery, and away you go!

That's exactly what 4-wheel parts told me when I called them. It could only pull back though....Kinda awkward not unless you install a hitch in the front of your vehicle.

stephen <img src="/forums/images/graemlins/cheers.gif" alt="" />


Exploring the outback is my game!

2005 Mitsu Gen3 Limited
OME Custom Suspension
Custom made safari roof rack
Garmin GPS
32X12.50X16 BFG Mud Terrain

1997 Mitsu Gen2 LS
Safari Roof rack
Garmin GPS
33x11.50x15 BFG MUds
Re: winch installation [Re: Gellekanao] #407716 02/28/04 04:50 AM
Joined: Jun 2003
Posts: 152
Gellekanao Offline OP
Wheeler
Thanks for all your help guys! I guess I'm stuck with the good ol' high lift jack <img src="/forums/images/graemlins/kewl.gif" alt="" />


thanks again,
Stephen


Exploring the outback is my game!

2005 Mitsu Gen3 Limited
OME Custom Suspension
Custom made safari roof rack
Garmin GPS
32X12.50X16 BFG Mud Terrain

1997 Mitsu Gen2 LS
Safari Roof rack
Garmin GPS
33x11.50x15 BFG MUds
Re: winch installation [Re: Gellekanao] #407717 02/28/04 05:44 AM
Joined: Jun 2003
Posts: 7,356
MontyMcV Offline
Trail Leader
It's possible to winch in the opposite direction. But you need lots of cable, pulleys, and a little luck with fixed anchors in the right places...

What about cutting a small hole in the front bumper to accomodate a pass through for what would amount to a receiver. Have it pass through to a plate that then spreads side-to-side so that it can tie into the frame rails. That is actually what I have been pondering on.

As for the 4-5k rating on the receiver, I'll bet the rating is more a function of the Montero's ability to tow safely across the roadways. Somebody posted on a thread a little while back that a pintle hook mounted to the back plate could handle 10k...


Big Truck: 00, 3.5, Endeavor, 5-Spd drive line in hand!
Little Truck: 87, 2.6T I/C, MT, LSDs, Tonneau Top
Her Truck: 03, 3.8, 20th Anniv, 65k
Daughter's: 06 Eclipse, Keeping it Mitsu!
FSMs: MitsubishiLinks.com
Re: winch installation [Re: MontyMcV] #407718 02/28/04 05:51 AM
Joined: Dec 2003
Posts: 1,063
N
NumLock Offline
Body Damage is Cool
yes some of the vans at work have trailer hitche on the front and back with red cables going to them. so they are for a winch? that is a very cool way to mount the winch.

thanks for the info.

Paul


88 Montero, 2'lift, 31X10.5, front locker.
"Because you're mine, I walk the line."
Page 2 of 2 1 2







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 0.012s Queries: 16 (0.009s) Memory: 0.6176 MB (Peak: 0.7212 MB) Data Comp: Off Server Time: 2026-11-17 13:49:26 UTC
Valid HTML 5 and Valid CSS