Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Need advice - reattaching speed sensor to t-case #453184 05/21/04 05:13 AM
Joined: Apr 2001
Posts: 1,103
R
rodeo_chris Offline OP
Body Damage is Cool
I'm an idiot and managed to break the clip that holds the speed sensor onto the transfer case.(94 Rodeo, V6, MUA5, speed sensor not cable)

For several months the cable stayed in place on its own. Tuesday it came loose on the interstate, speedo went to 0 and the CE light came on. I reset the CE light and used some duct tape to hold the sensor on there.

Kinda sporatically working now. What are my choices for keeping that thing on there for good? I'm leaning towards some JB Weld on the outer circumference of it unless someone can think of a reason this would interfere with its operation or a better idea. Let me know what you come up with.

-chris


94 Rodeo, 35's, 5.38's, locked F&R, Rocker bar on one side, other side in garage

96 Tacoma, DD, pre-dented
Re: Need advice - reattaching speed sensor to t-case [Re: rodeo_chris] #453185 05/21/04 03:26 PM
Joined: Apr 2002
Posts: 2,529
Bigpoppax2 Offline
Roll Me Over
You could get a big flat washer or a steel ring with a break in it(to get it over the cable) and drill some holes in the ring/washer then use some short self tappers to hold it to the t-case.

Of course you'd want to watch your depth on the self tappers. Don't know if I'd want to do anything quite as permanent as JB weld.


A gun in the hand is better than a cop on the phone.

98 Passport 33's, Supercharged, Calmini Bumper, rockbars, diff drops, Teralows, 4.77's, Aussie and ARB lockers, Safari snorkel, Optima red top.
Re: Need advice - reattaching speed sensor to t-case [Re: rodeo_chris] #453186 05/21/04 05:53 PM
Joined: Aug 1999
Posts: 9,030
randii Offline
4x4Wire.com Managing Editor Emeritus
I'd just replace the clip with the Isuzu-intended piece... is it not available individually?

The speed sensors that I have seen (admittedly all cable drives have a separate piece that retains them... describe what you have on your speed sensor?

Randii


Randy Burleson
4x4Wire Managing Editor Emeritus
Mongrel Isuzu Amigo
Re: Need advice - reattaching speed sensor to t-case [Re: randii] #453187 05/22/04 04:48 AM
Joined: Apr 2001
Posts: 1,103
R
rodeo_chris Offline OP
Body Damage is Cool
Quote
I'd just replace the clip with the Isuzu-intended piece... is it not available individually?

The speed sensors that I have seen (admittedly all cable drives have a separate piece that retains them... describe what you have on your speed sensor?

Randii


Not sure if it is available separately or not.

The piece that broke off was just a plastic clip. Kinda like the clips in the door jam on the wires that run to the doors. Push down on one side and lift on the other and they usually pop right out. Guess it just got too brittle over the past 10 years.

I'm headed home tomorrow where a proper repair will be attempted. My speedometer has been so far off for so long that I've gotten used to the drive by tach technique.

Thanks guys,
-chris


94 Rodeo, 35's, 5.38's, locked F&R, Rocker bar on one side, other side in garage

96 Tacoma, DD, pre-dented







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 7.762s Queries: 15 (0.007s) Memory: 0.6018 MB (Peak: 0.6578 MB) Data Comp: Off Server Time: 2026-11-17 14:32:48 UTC
Valid HTML 5 and Valid CSS