Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
GEN II sway bar removal for wheeling? #499824 09/09/04 10:41 PM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
My buddy has a tacoma (hes actually on these forums...)

anyways, he took off his sway bar and gained quite a bit of articulation (granted this would suck for normal highway driving)

could we/do we do this to our Gen II's? don't we also have a rear sway bar also? (i'm too lazy to leave my dorm and check right now smile )




also....one more question...would the lug pattern on a 98 Tacoma happen to be the same as my gen II?


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499825 09/10/04 04:31 AM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
ok seriously.....NO ONE HAS TRIED THIS????


isn't it a common trick to take of the sway bars to gain articulation on other vehivles? <img src="/forums/images/graemlins/confused.gif" alt="" />


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499826 09/10/04 04:57 AM
Joined: Sep 2002
Posts: 3,634
bretwalda Offline
Roll Me Over
I've done it to both of my Gen2's. Easy enough - should be able to get off by just removing the shocks. Removing the lateral rod and a spring will definitely make it even easier.


concreteprinter.com
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499827 09/10/04 03:08 PM
Joined: Apr 2004
Posts: 1,494
B
BobShaw Offline
Body Damage is Cool
It's not a trick, it is necessary for off road. Yes it makes the vehicle more unstable on the highway. Most of us use rims with a smaller rear backspacing and move the tires outward 2-4 inches per side. This gives you back some of the stability.
Bob Shaw


87 Raizer, 4.3V6, Mod TH700R4,231CHD, detroit rear and LSD front, bouncy seats, 2" lift and 32x15 BFG MT tires.
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499828 09/10/04 03:27 PM
Joined: Feb 2002
Posts: 3,548
Angelo Offline
Roll Me Over
***
Quote
also....one more question...would the lug pattern on a 98 Tacoma happen to be the same as my gen II?


Yes, it would.

Also, its not that hard to take the sway bars off. I currently have both my sway bars off, and yes, it gets tippy, but you just get used to it and you have to take it easy. I know, I know, I should put them back on, but havent gotten the chance to take the skids off and bolt it back on there. Just doing some testing <img src="/forums/images/graemlins/drunk.gif" alt="" /> <img src="/forums/images/graemlins/cheers.gif" alt="" /> <img src="/forums/images/graemlins/drunk.gif" alt="" /> <img src="/forums/images/graemlins/cheers.gif" alt="" /> <img src="/forums/images/graemlins/drunk.gif" alt="" />

later,
Angelo


99JAOS2"& OME 2"body 4.90s ARB HS9500i Skids&Ladder 16"315BFG JAOSRemote& Rack 3Row Rad IPF back& Searchlite HID Overhead Console/CB switchPanel FrARB RrLocker TJMSnorkel 160AAlt Sliders 2nd Tranny Cooler QuickAirII& Tank Rear frame/tank Lift
Re: GEN II sway bar removal for wheeling? [Re: bretwalda] #499829 09/10/04 07:51 PM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
you had to take your shocks off just to remove the sway bars? <img src="/forums/images/graemlins/confused.gif" alt="" />


did it seem to help much?


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: Angelo] #499830 09/10/04 07:54 PM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
Quote
Quote
also....one more question...would the lug pattern on a 98 Tacoma happen to be the same as my gen II?


Yes, it would.

Also, its not that hard to take the sway bars off. I currently have both my sway bars off, and yes, it gets tippy, but you just get used to it and you have to take it easy. I know, I know, I should put them back on, but havent gotten the chance to take the skids off and bolt it back on there. Just doing some testing <img src="/forums/images/graemlins/drunk.gif" alt="" /> <img src="/forums/images/graemlins/cheers.gif" alt="" /> <img src="/forums/images/graemlins/drunk.gif" alt="" /> <img src="/forums/images/graemlins/cheers.gif" alt="" /> <img src="/forums/images/graemlins/drunk.gif" alt="" />

later,
Angelo
how bad does it really drive? is it a subtle difference?

for instance, i was told my ride would be horrible after cranking my T-bars but i thought the difference was negligible <img src="/forums/images/graemlins/confused.gif" alt="" />

will taking these off affect anything else on the truck? make anything wear prematurely?


thanks guys

<img src="/forums/images/graemlins/smile.gif" alt="" />


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: BobShaw] #499831 09/10/04 11:25 PM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
Quote
It's not a trick, it is necessary for off road. Yes it makes the vehicle more unstable on the highway. Most of us use rims with a smaller rear backspacing and move the tires outward 2-4 inches per side. This gives you back some of the stability.
Bob Shaw
if its necessary, and more people do it, then how come the replies are so lacking? <img src="/forums/images/graemlins/frown.gif" alt="" />


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499832 09/10/04 11:52 PM
Joined: Dec 2000
Posts: 2,968
Big Blue Offline
Roll Me Over
You are lacking in replies as there are huge safety implications involved with removing them. I don't know you, or how you drive. What might be "safe" for you, may not be safe for the next ten people.
ANYTHING that compromises your handling on the road/hiways needs be thought about long and hard. How many people do you put at risk when you do this or that needs to be taken into consideration.
The gains are minor at best. Are you willing to remove them at each trailhead, and then re-install them before you head home after wheeling?
The removal of the rear anti-sway bar on some of our rigs allows for the trailing arms to fatigue much quicker, causing other possibly very ugly problems that could damage/destroy your truck and kill people. There are fixes/mods for those rigs, but until you do those mod's you should not remove your rear anti-sway bar.
IF you are talking about a "pure" trail rig that does not spend any time on roads/hi-ways, then sure pull them. BUT they are there to increase the safety of a vehicle that is already thought of by some to be tippy, and just plain un-safe, with a very high center of gravity. If you are involved in an accident, and while investagating the accident, it is found that the anti-sway bars were removed by the owner, you could be found at fault, even if the anti-sway bars had nothing to do with the accident.
NO-ONE should tell you that they are just fine without the anti-swaybars on them, as they don't drive where/what/when you do, and they don't know/drive your rig, under the conditions that you do.
OK, now you have a response.
Kary


1987 Mitsubishi Pajero "Modified"
The other original Mitsu brother
Northwest Trailmaster
Re: GEN II sway bar removal for wheeling? [Re: Big Blue] #499833 09/11/04 12:50 AM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
Quote
You are lacking in replies as there are huge safety implications involved with removing them. I don't know you, or how you drive. What might be "safe" for you, may not be safe for the next ten people.
ANYTHING that compromises your handling on the road/hiways needs be thought about long and hard. How many people do you put at risk when you do this or that needs to be taken into consideration.
The gains are minor at best. Are you willing to remove them at each trailhead, and then re-install them before you head home after wheeling?
The removal of the rear anti-sway bar on some of our rigs allows for the trailing arms to fatigue much quicker, causing other possibly very ugly problems that could damage/destroy your truck and kill people. There are fixes/mods for those rigs, but until you do those mod's you should not remove your rear anti-sway bar.
IF you are talking about a "pure" trail rig that does not spend any time on roads/hi-ways, then sure pull them. BUT they are there to increase the safety of a vehicle that is already thought of by some to be tippy, and just plain un-safe, with a very high center of gravity. If you are involved in an accident, and while investagating the accident, it is found that the anti-sway bars were removed by the owner, you could be found at fault, even if the anti-sway bars had nothing to do with the accident.
NO-ONE should tell you that they are just fine without the anti-swaybars on them, as they don't drive where/what/when you do, and they don't know/drive your rig, under the conditions that you do.
OK, now you have a response.
Kary


thank you. <img src="/forums/images/graemlins/shocked.gif" alt="" />


thats what I was wondering, my friend with the tacoma took his off for awhile and he said he could articulate quite a bit better. if the gains are minimal and outweighed by the negatives then this is one mod i will stay away from <img src="/forums/images/graemlins/wink.gif" alt="" />


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Page 1 of 3 1 2 3







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 0.011s Queries: 16 (0.008s) Memory: 0.6432 MB (Peak: 0.7700 MB) Data Comp: Off Server Time: 2026-11-17 11:15:50 UTC
Valid HTML 5 and Valid CSS