Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Page 2 of 3 1 2 3
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499834 09/11/04 06:51 PM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
can someone just confirm how much of a pain it is to remove the front sway bar? if it only takes 30 minutes to yank off then it wouldn't be a big deal to me to take it off for the trail and then put it back on afterwards.

I might hit up a trail about 30 minutes from here with my friends tacoma on 33's.

All i have are 31's so i'm gonna need all the help i can get
<img src="/forums/images/graemlins/lol.gif" alt="" />


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499835 09/12/04 05:38 AM
Joined: Sep 2002
Posts: 3,634
bretwalda Offline
Roll Me Over
The rear removal is questionable - the front - dont do it - especially on a Gen2 3.5, your brush guard on the front, you're asking for trouble. There's a whole lot more handling issues at stake. Edit: I see you wanna just unbolt for a ride - easy enough. Although the link between the bar and lower arm on mine was so rusted I had to cut mine off with a grinder - I'd make sure I can get it off before I head out and attempt it on the trail.

Misterbishi has in the works a batch of front sway disconnects but they are a long time coming <img src="/forums/images/graemlins/sleeping.gif" alt="" />. I have one of his early prototypes and it works great - and is the only way to deal with the front end IMO.

As far as the rear - you will get a ton more drop articulation - at least on the Gen 2. I cant even get my rear wheels off the ground unless I max out my 48" hilift to near-dangerous heights <img src="/forums/images/graemlins/ignore.gif" alt="" /> (and before anyone flames me please realize there's never a reason for me to not just jack on the rear axle - I'm just illustrating a point <img src="/forums/images/graemlins/wink.gif" alt="" />)

Pic of the front disconnected:

[Linked Image]

Rear sway removed:

[Linked Image]

Last edited by bretwalda; 09/12/04 05:47 AM.

concreteprinter.com
Re: GEN II sway bar removal for wheeling? [Re: bretwalda] #499836 09/12/04 07:59 AM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
Quote
The rear removal is questionable - the front - dont do it - especially on a Gen2 3.5, your brush guard on the front, you're asking for trouble. There's a whole lot more handling issues at stake. Edit: I see you wanna just unbolt for a ride - easy enough. Although the link between the bar and lower arm on mine was so rusted I had to cut mine off with a grinder - I'd make sure I can get it off before I head out and attempt it on the trail.

Misterbishi has in the works a batch of front sway disconnects but they are a long time coming <img src="/forums/images/graemlins/sleeping.gif" alt="" />. I have one of his early prototypes and it works great - and is the only way to deal with the front end IMO.

As far as the rear - you will get a ton more drop articulation - at least on the Gen 2. I cant even get my rear wheels off the ground unless I max out my 48" hilift to near-dangerous heights <img src="/forums/images/graemlins/ignore.gif" alt="" /> (and before anyone flames me please realize there's never a reason for me to not just jack on the rear axle - I'm just illustrating a point <img src="/forums/images/graemlins/wink.gif" alt="" />)

Pic of the front disconnected:

[Linked Image]

Rear sway removed:

[Linked Image]
when you say theres more than handling issues at stake.....what are you talking about? <img src="/forums/images/graemlins/confused.gif" alt="" />

are there other mods i should do first before taking off the sway bars?


anymore pics you want to post? <img src="/forums/images/graemlins/kewl.gif" alt="" />

preferably flex pics??? <img src="/forums/images/graemlins/notooth.gif" alt="" />


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499837 09/12/04 04:08 PM
Joined: Jan 2001
Posts: 3,876
Tag Offline
Roll Me Over
*****
Also cant it damage the shocks by overextending them?

I somewhere along the line want one of the things Bretwalda has on his front swaybar. What happened to the guy that had the air powered one? I think it was on the rear though.


89 2dr 3.0 AT, manual hubs. 33x12.5 MT
gen 2 coils,Cranked front tbars
Dons rocker protection, Front/Rear Bumpers. ARB rear locker, 2" BL, Beefed up skid plates/trailing arms. Gen II uca, 2 Bouncy seats www.youtube.com/TagGeorge
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499838 09/12/04 11:29 PM
Joined: Oct 2003
Posts: 715
socalmonty Offline
Rock Warrior
I have a Gen1 and removed both sway bars. To be honest, I didn't notice much of a difference on or off-road.


Sean - Orange County, CA
MAIL: seanwilliams78@gmail.com
1995 Montero SR - For exploring and getting away!
1994 Volvo 850 Turbo - 402hp and counting!
1966 VW Bug 2275cc - For stoplight drags!
Re: GEN II sway bar removal for wheeling? [Re: socalmonty] #499839 09/29/04 09:45 PM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
bump, in case anyone wants to speak more on this subject.



Bretwalda said something about there being too much risk, especially with my front brush guard---just for removing the front.


can you please elaborate more? i joined the 4wd club at my college and we are going to Disney, OK for a trip next month. I want to know what exactly you meant by that comment before I take off the front sway bar for the trip.


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499840 09/29/04 10:42 PM
Joined: Jan 2000
Posts: 16,227
off-roader Offline
Web Wheeler
*****
Teaque,

There's not much to say on this subject. Many have removed their rears and left their fronts on because their rigs are also daily drivers.

Until you try it yourself, it's almost no use asking how the rig will handle, etc. If you do try it, be sure to check just how much articulation you gain (measure it) and also keep in mind by removing it your suspension will be more complaint which may be another result you're after.

Myself I run w/out the rear sway bar. I used to run a set of quick disconnects for the rear but that ended in Moab 3 years ago when I pretzel'd the bar on a rock.

Since then, I've been w/out the rear bar but then again, I don't try to drive anywhere near as fast as a car when going on curves and am always drive alert to what's going on around me. That's no guaranty that nothing will happen but it's a "calculated risk" I'm willing to take.

Wheel back spacing... I should also point out that in most cases, tire sizes are increased when this is done and there have been substancial discussion as to whether the increase in height versus the increase in width raises the COG which is directly related to how safe the rig will be with the sway bars removed.

As was pointed out... [disclaimer on]There is a risk and liability involved for anyone who removes them so just bear that in mind if you remove yours.[disclaimer off]<img src="/forums/images/graemlins/kewl.gif" alt="" />


Off Roader
98 Montero with the Winter Package
89 Montero minty clean and reserved for overlanding trips or Cars and Coffee events
96SR (3.15:1 xcase, 35's) gone to the rust gods
96SR Build Up Thread
Old web page
Old web page
Re: GEN II sway bar removal for wheeling? [Re: off-roader] #499841 09/29/04 11:12 PM
Joined: Nov 2003
Posts: 167
TeaQue Offline OP
Wheeler
Thanks for the reply. I guess I was just more or less wondering what he meant by me being more at risk because I have a brush guard <img src="/forums/images/graemlins/confused.gif" alt="" />



anyone know if i will over extend the shocks on the rear on a Gen II for sure?

they are stock shocks....


1997 Montero LS
3.5 V6
31x10.5 BFG A/T's
T-bar lift
Optima Yellow Top
Cheap Pilot Fog lights
Re: GEN II sway bar removal for wheeling? [Re: TeaQue] #499842 09/30/04 03:45 AM
Joined: Apr 2004
Posts: 1,494
B
BobShaw Offline
Body Damage is Cool
I would think that you would not overextend the shocks. The swaybar does not keep both wheels from dropping together the same distance.
The Gen I front (did not have a rear?) needs to be removed completely or it will bang against the lower A arm and the steering linkage, if just loosened. I would definintly advise wheels with a smaller rear offset to move the tires outboard for more stabililty. Yes it can be squirley on the highway at high speeds W/O the swaybar.
4WD's are built not bought.
Bob Shaw


87 Raizer, 4.3V6, Mod TH700R4,231CHD, detroit rear and LSD front, bouncy seats, 2" lift and 32x15 BFG MT tires.
Re: GEN II sway bar removal for wheeling? [Re: BobShaw] #499843 09/30/04 07:12 AM
Joined: Jan 2000
Posts: 16,227
off-roader Offline
Web Wheeler
*****
Bob, unlike the leaf sprung I-4's the coil sprung v6's have a rear anti-sway bar.


Off Roader
98 Montero with the Winter Package
89 Montero minty clean and reserved for overlanding trips or Cars and Coffee events
96SR (3.15:1 xcase, 35's) gone to the rust gods
96SR Build Up Thread
Old web page
Old web page
Page 2 of 3 1 2 3







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 2.525s Queries: 16 (0.020s) Memory: 0.6472 MB (Peak: 0.7768 MB) Data Comp: Off Server Time: 2026-11-17 13:50:52 UTC
Valid HTML 5 and Valid CSS