The biggest problem with using the 4L60 is the offset transmission pan. The Isuzu t-case doesn't quite have the reach to easily clear the pan. I'm not saying it won't clear, but you may need to clock the t-case a little and/or cut the corner out of the tranny pan to fit a driveshaft by it. Here's what I mean:
[Linked Image]


The TOD case, I think, may have a little bit more reach so it clears the pan better. Another option is to use a 2-piece front driveshaft with a carrier bearing. This leads to a very short front piece of the shaft, but with IFS it doesn't matter since the diff doesn't move.

For tranny control you have a couple options. There's always the manual valve body option. This will work with the newer 4L60-E's with the removable bell housing as well. On the 4L60-E, it removes the electronics and makes it full-manual shifting. Just like a manual tranny, but no clutch. You would still wire in a switch for the torque converter lockup.

Another problem. There are 2 different types of 4L60 tranny bodies. The earlier versions all had 1-piece bodies. The bell is built in. Starting in '96, they used a 2-piece w/ removable bell housing (see the pic above). This 2-piece also has a different, 6-bolt tail housing pattern. The older style has a 4-bolt pattern.

This adapter that you mentioned:


will not work with the 1-piece tranny housing. It is a 6-bolt hex pattern adapter that will bolt only to the later 2-piece housing. If you want to do this with existing parts, you need:

2-piece 4L60-E transmission ('96 and later).
60 deg V-6 pattern bell housing for it ('96 and later 3.8 camaro/firebird)
"small" torque converter (same camaro/firebird)
The adapter plate shown above.
Tranny control (either a spendy, near $1000 aftermarket controller or a full manual valve-body)
And likely a 2-piece front driveshaft to clear the pan.

Another option is to use a Dana 300 transfer case. With this you can use:
A 1-piece TH700/4L60 from an S-10 (no electronics other than TC lockup)
Existing TH700 - Dana 300 adapter ($300 - $400 I think. Ask Dallas).
torque converter from S-10 as well.
Custom or aftermarket shifter setup for D300 (twinstick is a worthy option)

This t-case will clear the tranny pan and give you a 2.6: ratio stock. You can also get 2 Dana 44 pinion flanges from 1st gen Rodeo's (~$40), or 2nd gen Rodeo/Amigo (~$60) and they will bolt right on to the front and rear output shafts of the Dana 300. This will give you the Zu flanges you want. All you need to do is lengthen/shorten the driveshafts as needed.
[Linked Image]


And if that isn't enough, you still have the A340 options as well. See my old post Oh no, jeep parts!!

I'm still working on the AW4 to 60 deg bell housing matchup. The bell is about $350 new from Isuzu, and I haven't worked out the flexplate & torque converter issues (whether stock parts will work or if custom ones are needed). I'm still looking, but there may be a cheaper bell used on the late-80's Cherokee that bolted to the 4-cyl motor at that time that had the same 60 deg bell housing pattern. (This is the same pattern you need for the 3.2/3.5 BTW).

There is an adapter for this tranny to the Zu t-case as well from the '03 and up Isuzu's. This will let the Zu t-case bolt up to the AW4, but I'm not sure on spline counts. If the '03 Zu tranny is 27 spline (like the previous Zu autos and t-cases), the Zu case should bolt right up. If not, it'll take some more work to do, involving a spacer plate and conversion shaft.

--Dan