Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Axles #512650 10/12/04 09:43 PM
Joined: Feb 2004
Posts: 81
R
rebelboydylan Offline OP
Getting the Wheeling Fever
My dana 35 axle broke and i need to get a bigger axle is there any junk yard axle like a dana 44 that would bolt right up?


91 yj renegade with 4.5" lift 33x10.5s wanting to be a rock eatin machine
Re: Axles [Re: rebelboydylan] #512651 10/12/04 11:26 PM
Anonymous
Unregistered
the only axle that will bolt up is another dana 35c. all other axles will need some degree of work unless you order one from a company like pro rock or curry. any other axle will need modifications some where, the most common will be converting from spring over to under.

Re: Axles [Re: rebelboydylan] #512652 10/12/04 11:27 PM
Joined: Jun 2003
Posts: 442
kobyhud Offline
Mudrunner
You are going to get a lot of answers on this one.

But for starters we need some more information.
What is your current gear ratio??? Do you want to lock it at the same time? How serious are you?? What do you use it for? Would a limited slip suffice?? Etc...

A little information can go a long way.


95 Rodeo LS, Auto, SAS, , 60 front, 14 bolt rear. 5.13 r&p, Hydro-Assist, teras..
http://www.pieceofhud.com/gallery
Re: Axles [Re: kobyhud] #512653 10/13/04 02:22 AM
Joined: Oct 1999
Posts: 2,211
S
superdawg Offline
Body Damage is Cool
Comanchee d44 is the closest to "bolting up"
Just the spring mounts need to be cut of and new ones welded on.
Call mitch at RMH he has a few of these for sale.

303-808-1268

SD

Re: Axles [Re: kobyhud] #512654 10/13/04 02:23 AM
Joined: May 2004
Posts: 927
Macka Offline
Rock Warrior
I am sure some of the guys who still have 35's hanging around their shop/yard after doing a swap would be able to help. IMO if you have the $$$ get a 44 upgrade done.


always working
Re: Axles [Re: Macka] #512655 10/13/04 02:56 AM
Joined: Feb 2004
Posts: 81
R
rebelboydylan Offline OP
Getting the Wheeling Fever
i have a 91 wrangler with a 4.5 suspention lift and 33x10.5 i'd say i'm off roading 25% of the time other on road this is my second 35 i'v went through i'd like to put a dana 60 in or a ford 9" but time is a issue for this project


91 yj renegade with 4.5" lift 33x10.5s wanting to be a rock eatin machine
Re: Axles [Re: rebelboydylan] #512656 10/13/04 04:11 PM
Joined: Jun 2003
Posts: 442
kobyhud Offline
Mudrunner
for a Dana60 or 9" it is going to be a job or lots of $$$s. The axles will have to be narrowed, most likely you could match up a gear ratio but it really isnt going to matter because its going to have to be pulled apart to narrow it anyway.

To find something with your current gear ratio I would look for a Wagoneer 44 that is a little wider and has disk brakes. Common ratios here are 3.73. This is probably the easiest option.

If you were willing to regear the front as well you could find an isuzu 44 with a G80 (chevy/GM) limited slip for pretty cheap. This would be a great width but the gears would be either 4.10 or 4.30. Which wouldnt be bad if you could find a Dana30 from a 4cylinder Wrangler with the 4.10 gears. You could be out the door with lower gears and a limited slip for less than a grand if you went with this route with disk brakes as well.


95 Rodeo LS, Auto, SAS, , 60 front, 14 bolt rear. 5.13 r&p, Hydro-Assist, teras..
http://www.pieceofhud.com/gallery
Re: Axles [Re: kobyhud] #512657 10/13/04 05:17 PM
Anonymous
Unregistered
Quote
To find something with your current gear ratio I would look for a Wagoneer 44 that is a little wider and has disk brakes. Common ratios here are 3.73. This is probably the easiest option.


Actually a Waggie rear is a little bit narrower. His 35 is 60" and a Waggie 44 is about 58". The wheel pattern will be different than the front axle though. A Ford 8.8 out of a 95 or newer Explorer has the right wheel pattern and disc brakes to boot. Either one is going to take a bit of fabrication (not hard stuff) to make work.

Re: Axles #512658 10/13/04 10:34 PM
Joined: Jun 2003
Posts: 442
kobyhud Offline
Mudrunner
you can find waggies all the way out to 63 inches wide.... you are correct about the wheel pattern... 6on5.5 isnt going to match the front.

The ford 8.8 is just a little narrower like 59", has disks, could have a limited slip as well... another great option probably going to have to regear the front though, but again you could find a 4 cylinder D30 with 4.10s and have a grand old time. lighter than a 44 as well. Axle clearance isnt quite as good, but not enough to really matter.


95 Rodeo LS, Auto, SAS, , 60 front, 14 bolt rear. 5.13 r&p, Hydro-Assist, teras..
http://www.pieceofhud.com/gallery
Re: Axles [Re: kobyhud] #512659 10/14/04 11:44 PM
Anonymous
Unregistered
Quote
you can find waggies all the way out to 63 inches wide....


Not on a rear axle. Waggies are only available narrow track. Front is 62.5" and the rear is about 58". Now a Cherokee Chief or J-truck 44 is wider. Front is about 65" and the rear is about 61". I have at least one set of each in my shop.


Moderated by  4x4Wire 







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 0.013s Queries: 14 (0.010s) Memory: 0.6265 MB (Peak: 0.7342 MB) Data Comp: Off Server Time: 2026-11-18 12:08:15 UTC
Valid HTML 5 and Valid CSS