should I "flip" the ball joint on a calmini upper control arm?

4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums

Register Log In 4x4Wire TrailTalk Forums Isuzu 4x4 & SUV Talk should I "flip" the ball joint on a calmini upper control arm?

Print Thread

Rate Thread

Re: should I "flip" the ball joint on a calmini upper control arm? [Re: duffin_p] #547759 01/06/05 08:20 AM

Anonymous

Unregistered

With the "Springz Upgrade" and Calmini shackles you will most likely be higher than 3". I'm not sure what the maximum recommended lift for the front is, but it seems a lot of people run the full DOR lift without problems. The main drawback of going over 2.5 - 3" in the front is that the ride comfort suffers exponentially. Also, with over 3" lift you'll probably want to go to a one piece driveshaft.

Entire Thread
Subject	Posted By	Posted
should I "flip" the ball joint on a calmini upper control arm?	duffin_p	01/05/05 05:29 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	RobG	01/05/05 05:47 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	duffin_p	01/05/05 06:07 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	Anonymous	01/05/05 09:37 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	strawmyers	01/05/05 06:49 PM
Re: should I "flip" the ball joint on a calmini upper control arm?	duffin_p	01/05/05 11:01 PM
Re: should I "flip" the ball joint on a calmini upper control arm?	Rodeo Clown	01/05/05 11:19 PM
Re: should I "flip" the ball joint on a calmini upper control arm?	Anonymous	01/06/05 08:20 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	mlclark	01/06/05 08:43 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	Sammy	01/06/05 08:44 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	mlclark	01/06/05 09:12 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	Paddler	01/06/05 04:05 PM
Re: should I "flip" the ball joint on a calmini upper control arm?	lttlbddy	01/07/05 02:50 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	duffin_p	01/07/05 03:19 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	Sammy	01/07/05 03:35 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	lttlbddy	01/07/05 04:26 AM
Re: should I "flip" the ball joint on a calmini upper control arm?	Sammy	01/05/05 06:55 PM
Re: should I "flip" the ball joint on a calmini upper control arm?	Paddler	01/05/05 07:45 PM
Re: should I "flip" the ball joint on a calmini upper control arm?	duffin_p	01/05/05 10:56 PM

Moderated by 4x4Wire, houlster, jezeric, Jim_Paget, strawmyers

Hop To

4x4Wire Social:

| 4x4Wire on FaceBook |

OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

PHP: 7.4.33 Page Time: 3.434s Queries: 16 (3.431s) Memory: 0.6326 MB (Peak: 0.6655 MB) Data Comp: Off Server Time: 2026-06-19 10:56:55 UTC
Valid HTML 5 and Valid CSS