Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Leaky Diff #56846 06/23/03 09:36 PM
Joined: Jan 2000
Posts: 539
Terry4X4 Offline OP
Rock Warrior
Weekend before last I scrubbed the rear diff a couple of times on the Rubicon and eventually tore out the rear diff plug. I borrowed a spare and qt of gear oil and was back on the trail. Since then the diff had been dripping on the driveway at home. Last week I picked up a new plug and yesterday went to put it in. The threads on the borrowed plug got hosed pretty good. I gently put my finger in the hole and felt the threads and they were pretty hosed as well from the plug being ripped out. I raced to the hardware store before they closed and got a tap to redo the threads. After tapping the threads, the new plug went in normally and appeared to seat properly. However, now it is leaking worse than previously.

I thought about using some RTV around the plug to seal it up. However, thinking about removing it in the future seems like it will be a PITA. Any other suggestions to stop the leaky rear diff?


Terry Johnson
Gettin' Off 4X4 Club
'89 XCab SR5 V6 - D60 Hybrid SAS, Ultimate Marlin Crawler, Detroit rear, ARB front
'97 TJ - Atlas 3.8 Twin Stick, ARB F&R, custom rollcage
Re: Leaky Diff #56847 06/23/03 09:50 PM
Joined: Nov 2000
Posts: 4,192
DirtyHarry Offline
Toyota Moderator
Well you could get one of Roger's plates and shave the bottom of the diff, that would take care of the problem. <img border="0" title="" alt="[Big Grin]" src="images/icons/grin.gif" />

Short of that, I don't see why using RTV would be a problem, other than the fact that you will have to drain the diff again and clean it will before applying the silicone.

Re: Leaky Diff #56848 06/23/03 10:41 PM
Joined: Jan 2000
Posts: 12,153
4Crawler Offline
Web Wheeler
*****
Here's another option that I used to run on my axles:

Diff plug fix

Re: Leaky Diff #56849 06/23/03 10:51 PM
Anonymous
Unregistered
Weld that sucker!! <img border="0" title="" alt="[Big Grin]" src="images/icons/grin.gif" />

Re: Leaky Diff #56850 06/23/03 11:00 PM
Joined: Jan 2000
Posts: 10,859
little_joe Offline
Former Admin
*****
Use Hylomar from Permatex on the threads. If it can stop the leaks on my Rover, Toyota leaks should be no problem. It's real easy to work with and the plug can be removed/installed w/o having to redo it each time.


4x4Wire's Toyota Section
1995 FZJ80 LandCruiser - 3 locking diffs, +200k mi, JD HIR's, 285/75R16 Nitto TG's
Olde North State Cruisers
Re: Leaky Diff #56851 06/23/03 11:05 PM
Anonymous
Unregistered
</font><blockquote><font size="1" face="Verdana, Tahoma, Arial, Helv, Helvetica, Sans">quote:</font><hr /><font size="2" face="Verdana, Tahoma, Arial, Helv, Helvetica, Sans">Originally posted by Leonel Quinteros:
<strong>Weld that sucker!! <img border="0" title="" alt="[Big Grin]" src="images/icons/grin.gif" /> </strong></font><hr /></blockquote><font size="2" face="Verdana, Tahoma, Arial, Helv, Helvetica, Sans">Worked for me <img border="0" title="" alt="[Big Grin]" src="images/icons/grin.gif" /> <img border="0" title="" alt="[Big Grin]" src="images/icons/grin.gif" />

Re: Leaky Diff #56852 06/23/03 11:39 PM
Joined: Jan 2000
Posts: 539
Terry4X4 Offline OP
Rock Warrior
Thanks guys. I'm aware of the welded plug option, I just don't want to go there yet if I don't have to. <img border="0" alt="[Baby]" title="" src="graemlins/baby.gif" />


Terry Johnson
Gettin' Off 4X4 Club
'89 XCab SR5 V6 - D60 Hybrid SAS, Ultimate Marlin Crawler, Detroit rear, ARB front
'97 TJ - Atlas 3.8 Twin Stick, ARB F&R, custom rollcage
Re: Leaky Diff #56853 06/24/03 01:29 AM
Joined: Jan 2000
Posts: 12,153
4Crawler Offline
Web Wheeler
*****
Might be able to find an oversize plug and have the hole drilled and tapped for that. Looks like 3/4" or a 1/2" NPT thread would be a bit larger than the existing 18mm size.

Re: Leaky Diff #56854 06/24/03 03:36 AM
Anonymous
Unregistered
Do what I did:

<img src="http://www.yankeetoys.org/KLF/Taz2/AxleShave/RearShave3.jpg" alt=" - " />

Re: Leaky Diff #56855 06/25/03 11:55 PM
Anonymous
Unregistered
I resisted it too, but after loosing the front and almost loosing the rear (both low profile hex plugs) at the Hammers last spring I welded mine. It is really not that hard to drain through the studs and then you never need to worry about it again. Simple, free and done.

Page 1 of 2 1 2

Moderated by  4Crawler, 4x4Wire, kewlynx 







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 0.022s Queries: 15 (0.019s) Memory: 0.6311 MB (Peak: 0.7534 MB) Data Comp: Off Server Time: 2026-11-19 05:32:53 UTC
Valid HTML 5 and Valid CSS