Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
Crankshaft pulley problems & MORE!-help requested #686644 01/16/06 08:41 PM
Joined: Dec 2005
Posts: 23
M
Mulerider Offline OP
Need a Spot
Newbie here; I posted back in mid-Dec that my recently acquired 88 Trooper had suffered from crankshaft pulley failure. Lots of sudden noise, and you could turn and move around the pulley by hand.
Got the part from Jerry Lemond, and finally today pulled the fan and radiator.
What was under the fan shroud? The crankshaft bolt! Boogered threads, maybe but not likely usable. Whut happened..
It get worse; the rubber portion of the balancer had not come apart, instead the pulley had broken, leaving a portion on the crank. As the bulk of it came off (I'm guessing here..), it clipped the cambelt sprocket, removing a 1-1/2x1/2" chunk.
That must have happened as I started and drove the crippled thing onto the trailer, as then it went to "no-start" mode trying to unload it.
Cambelt got broke in the process. So....assuming I get off the remainder of the crank pulley, then pull (?) off the cambelt sprocket..geez <img src="/forums/images/graemlins/frown.gif" alt="" />

So I need: crank bolt, cambelt sprocket, and do a search here for sprocket/belt alignment.
So much for using the starter technique for crank bolt removal....my Trooper did it for me!

I think I saved Jerry's e-mail and phone #.

Thanks in advance for any tips or feedback...I'm working w/o a manual, just this site for help.

Added: just ordered the Haynes manual...I think I'll need it.

Last edited by Mulerider; 01/16/06 09:24 PM.
Re: Crankshaft pulley problems & MORE!-help requested [Re: Mulerider] #686645 01/16/06 11:08 PM
Joined: Apr 2003
Posts: 234
D
dvtrooper Offline
Wheeler
Mulerider, sorry to hear about your bad luck i will look around my garage i have some spare engine parts, i will let you know if i find what you need. Don


sua dana 44 conversion 5.38 gears, 4.3tbi,700r,dana 300 w/tera low 4:1 gears
Re: Crankshaft pulley problems & MORE!-help requested [Re: Mulerider] #686646 01/16/06 11:35 PM
Joined: Apr 2003
Posts: 898
litnin Offline
Rock Warrior
You might want to be prepared to check some valves.
If the belt broke while the engine was running,
there's a good change you bent some valves.


1995 Trooper LS auto 3.2 DOHC /w SOHC intake
1989 Trooper 2.6 auto
1989 I-Mark RS DOHC 1.6
1991 Stylus XS DOHC 1.8
Re: Crankshaft pulley problems & MORE!-help requested [Re: litnin] #686647 01/17/06 12:16 AM
Joined: Dec 2005
Posts: 23
M
Mulerider Offline OP
Need a Spot
There is enough left of the timing belt sprocket to put a puller on it; it is just pressed on?

And the crankshaft key looks really bad, so that's another issue.

Why for did Isuzu run a transmission line (looks like trans oil...) across the front? Drip,drip, drip.....

Re: Crankshaft pulley problems & MORE!-help requested [Re: Mulerider] #686648 01/17/06 12:32 AM
Joined: Aug 1999
Posts: 9,030
randii Offline
4x4Wire.com Managing Editor Emeritus
Quote
Why for did Isuzu run a transmission line (looks like trans oil...) across the front? Drip,drip, drip.....

That's a power-steering 'cooler' line.

Randii

Re: Crankshaft pulley problems & MORE!-help requested [Re: randii] #686649 01/17/06 01:58 AM
Joined: Apr 2000
Posts: 7,268
Happy Birthday mlclark Offline
Isuzu Moderator
*****
That's a power-steering 'cooler' line.

No, that is the PS pump supply line. The cooler loop is down below on the rad support. <img src="/forums/images/graemlins/smile.gif" alt="" />

Michael

Re: Crankshaft pulley problems & MORE!-help requested [Re: mlclark] #686650 01/17/06 02:21 AM
Joined: Dec 2005
Posts: 23
M
Mulerider Offline OP
Need a Spot
"No, that is the PS pump supply line. The cooler loop is down below on the rad support.

Michael"



Oops...as soon as I was back at the Trooper, the line was easily seen going to the power steering pump.

Back to my real concern....

Re: Crankshaft pulley problems & MORE!-help requested [Re: Mulerider] #686651 01/17/06 03:32 AM
Joined: Apr 2000
Posts: 7,268
Happy Birthday mlclark Offline
Isuzu Moderator
*****
Oops...

You made no mistake. Randii, OTOH, did. <img src="/forums/images/graemlins/smile.gif" alt="" />

Michael

Re: Crankshaft pulley problems & MORE!-help requested [Re: mlclark] #686652 01/17/06 06:00 AM
Joined: Aug 1999
Posts: 9,030
randii Offline
4x4Wire.com Managing Editor Emeritus
It happens. <img src="/forums/images/graemlins/pfft.gif" alt="" />

Randii (mine is a cooler now)

Re: Crankshaft pulley problems & MORE!-help requested [Re: randii] #686653 01/17/06 02:48 PM
Joined: Dec 2005
Posts: 23
M
Mulerider Offline OP
Need a Spot
"There is enough left of the timing belt sprocket to put a puller on it; it is just pressed on?"

Anyone had to remove/replace the sprocket?
`88 Trooper 2.6L

Page 1 of 3 1 2 3







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 0.013s Queries: 15 (0.010s) Memory: 0.6379 MB (Peak: 0.7618 MB) Data Comp: Off Server Time: 2026-11-18 22:38:09 UTC
Valid HTML 5 and Valid CSS