Extreme Terrain
4x4Wire Trail Talk Forums: Jeep, Toyota, Mitsubishi, Pajero, Isuzu, Kia, 4WD, 4x4, SUV, Off-Road and OutdoorWire Forums


Previous Thread
Next Thread
Print Thread
Rate Thread
Page 2 of 2 1 2
Re: What is this and is it hard to replace??? [Re: Tygger] #776191 01/02/07 04:43 AM
Joined: Aug 1999
Posts: 9,030
randii Offline
4x4Wire.com Managing Editor Emeritus
Quote
In the mean time, what type of grease do I need to keep things lubricated? Do I just paste the grease in to the opening?

Just about any grease is better than nothing, but most auto parts stores should be able to give you grease designed for CV joints. If you want a slightly longer-term fix, saran-wrap the joint after you grease it, and zip tie each side -- it sounds half-assed (and is), but it works surprisingly well.

Randii

Re: What is this and is it hard to replace??? [Re: randii] #776192 01/03/07 02:11 PM
Joined: Jun 2003
Posts: 262
T
Tygger Offline OP
Mudrunner
Thanks for all the info! You guys are awesome!

In the mean time, I think I'll try the syran wrap trick until I have some time to try and fix this correctly. I don't know how long it's been ripped. Should I attempt to clean it before adding more grease? If so, what's the best way to clean the dirt out?

Is the only purpose of the boot to prevent water, dirt, etc. from getting into the cv joints?

Thx again


1997 Isuzu Rodeo S 4WD
Re: What is this and is it hard to replace??? [Re: Tygger] #776193 01/03/07 03:55 PM
Joined: Aug 2002
Posts: 3,007
Richard Saylor Offline
Roll Me Over
*****
Quote
Is the only purpose of the boot to prevent water, dirt, etc. from getting into the cv joints?


Pretty much. Basically it's to keep the grease in the joint and the muck out of it.

Richard <img src="/forums/images/graemlins/patriot.gif" alt="" />


Had an 89 Isuzu Pickup
Had a 94 Mitsubishi Eclipse
84 Honda XL185S
Had an 89 Isuzu Trooper w/ 3.4 V6
01 Toyota Tundra SR5 V8 4Door Access Cab
http://community.webshots.com/user/rsayloriii
Re: What is this and is it hard to replace??? [Re: Tygger] #776194 01/03/07 08:07 PM
Anonymous
Unregistered
DO NOT LET THIS SCARE YOU! I had the same thing happen and printed the instructions with pictures from this website. The first one took about four hours, the other side took about 45 minutes. It looks daunting but if you have the tools, a jack and jackstands and a great deal of patients, you'll save yourself hundreds$$$$. It's one of those jobs where the parts are under $30 and the labor is insane. JUST DO IT.

Re: What is this and is it hard to replace??? #776195 01/04/07 02:08 PM
Joined: Jun 2003
Posts: 262
T
Tygger Offline OP
Mudrunner
Thanks for the encouragement. I re-read the instructions and think it just sounds harder than it is...

Looks like tools I would need are: jack, jack stands, basic sockets/racthet, pry bar and hammer. Am I missing anything?

Now I just need to find a free weekend to do this smile


1997 Isuzu Rodeo S 4WD
Re: What is this and is it hard to replace??? [Re: Tygger] #776196 01/12/07 05:43 PM
Joined: Jun 2003
Posts: 262
T
Tygger Offline OP
Mudrunner
What chemical (grease remover) should I use to clean out the old gunk???


1997 Isuzu Rodeo S 4WD
Re: What is this and is it hard to replace??? [Re: Tygger] #776197 01/12/07 05:55 PM
Joined: Aug 2002
Posts: 3,007
Richard Saylor Offline
Roll Me Over
*****
I just used carb cleaner. Just wipe out as much grease as you can with a rag, then hose it down with carb cleaner. Worked well for me. <img src="/forums/images/graemlins/kewl.gif" alt="" />

Richard <img src="/forums/images/graemlins/patriot.gif" alt="" />


Had an 89 Isuzu Pickup
Had a 94 Mitsubishi Eclipse
84 Honda XL185S
Had an 89 Isuzu Trooper w/ 3.4 V6
01 Toyota Tundra SR5 V8 4Door Access Cab
http://community.webshots.com/user/rsayloriii
Re: What is this and is it hard to replace??? [Re: Richard Saylor] #776198 01/15/07 05:40 AM
Anonymous
Unregistered
If you have auto locking hubs this would be a good time to clean them out and get them working right. Mine were not releasing.

I know this sounds wierd but you'll need a fishing scale to put them back together.

Re: What is this and is it hard to replace??? #776199 01/15/07 06:06 AM
Joined: Aug 1999
Posts: 9,030
randii Offline
4x4Wire.com Managing Editor Emeritus
Too much grease is as much a problem as too little -- there needs to be a film of grease for the parts to slide.
* too little grease and the bits will rust
* too much grease and the bits will essentially hydro-lock

There's limited room inside the hub, and if there's too much grease, that grease will block off that room.

Randii


Randy Burleson
4x4Wire Managing Editor Emeritus
Mongrel Isuzu Amigo
Re: What is this and is it hard to replace??? #776200 01/15/07 05:16 PM
Joined: Apr 2000
Posts: 7,268
mlclark Offline
Isuzu Moderator
*****
I know this sounds wierd but you'll need a fishing scale to put them back together.

Only if you are repacking the wheel bearings. For changing/repacking the CVs or cleaning/lubing the hubs, the pull-scale is not needed.

Good Luck,
Michael

Page 2 of 2 1 2







4x4Wire Social:

| 4x4Wire on FaceBook |


OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.

Powered by UBB.threads™ PHP Forum Software 7.7.3
(Release build 20190728)
PHP: 7.4.33 Page Time: 0.021s Queries: 15 (0.015s) Memory: 0.6363 MB (Peak: 0.7594 MB) Data Comp: Off Server Time: 2026-11-16 13:21:00 UTC
Valid HTML 5 and Valid CSS