There's a place in Fonthill (about 20 min from niagra falls) where i'm going to pick some up. Damplifier is about $3.50 / sq ft. Oh yeah, anything that comes on a "roll" or is rolled up, isn't meant for cars, it's meant for roofing. If it comes in sheets, it's meant for a car. I've learned that in my searching (dynamat extreme and damplifier come in sheets) The b-quiet stuff comes in rolls (made in alberta) .
Here's a cool site: http://www.sounddeadenershowdown.com/

had an hour today ... so I thought I would start on the floors .. got them drilled , and fit again , and started to "plug" the holes ..

got a couple done and ran out of wire .. crap !! I hate when that happens <img src="/forums/images/graemlins/zombie.gif" alt="" /> <img src="/forums/images/graemlins/angry.gif" alt="" />



.

tacked !!! <img src="/forums/images/graemlins/smile.gif" alt="" />
still have to modify the seat crossmembers to fit (there just sitting there ) and weld the nuts before I can weld them in --- but kind of shows you the seat support .









.

couple of things today ..
got the seat belts installed / mocked up
I do have to still plate the mouinting bolts on the floor , but I will do that when I have the cab off .



also removed the air intake muffler , and made a pipe . this pipe diameter is 2.75" and seems no one in town has .




.

continued with the floor mock up ...
but first had to replace the seat tracks .... some one cut and welded the rails >:(
i'm going to re-do the seats anyway , so no biggie !!



removing the seat back cover , lock strip and hog rings .





and installing the new rails ...



with the new rails , I now could line up the rail , and weld mounting bolts .. and zinc .







aligned , and welded



and seats ... BOLTED





[img]http://i76.photobucket.com/albums/j2/bj_bumperboy/MY%20Trekker/HPIM1381.jpg[/img]


.

couple of more things ....

buttoned up the heater control valve , and hoses including the rear heater piping ...



also

got the new fan installed .. I decided to take back the 14" 1500CFM in favor for the 16" .. 2500 CFM

had to cut the lower support .. but no biggie ..



made a new hood lock support , "boltable"




just now waiting for the fan controller now .. :-/ (ordered a week ago )



.

so not much to add ... built the box for the body computer .. and I'm just awaiting my new fenders to check clearances .. I want to move out as far as I can to alow for inner kick panel clearance ..



also got my new Optima battery



and also just got to day for the wiring near the exhaust ... some heat tape

sweeeeet, awesome job. kinda envy how you have the space and time to do this work...by the way, is that heater valve oem? aloha. <img src="/forums/images/graemlins/kewl.gif" alt="" />

thanks , I wish I had more space and time .. fishing and camping soon , and also coaching my boys ball team ... not much time for me .

Yes heater control valve is from a 89 4Runner 3.0L with rear heater . hoses and all fit excellent . I changed the routing of the rear piping for the rear heater though , I am using 14" of copper for each line , only to get by the crossover pipe , then I'm going to route rubber hose , and insulate it for better rear heat .

so spent a few bucks today ...
bought some shop tools and consumables , and some dollies . I wanted to put some tires and wheels on it , and the dollies will just make it that much more maneuverable ..

so .. I put the shoes on for mock up (they dont fit quite right as they hit the calipers) and got it on the dollies .. also got the fiber fenders set on to check the body computer box clearance .. fits perfect , so now I can weld that ....

so now I can push it around the shop .. I thought I would do a full body mock up ... hehehe .... enjoy .. I did