|
|
|
|
intake manifold torque specs 99 rodeo lse 3.2v6
#856868
01/02/08 08:02 PM
|
Joined: Jan 2008
Posts: 5
OP
Need a Spot
|
the haynes manual states 17lbs torque on the lower intake, does anyone have any updates on this tourqe spec as well as the plenum? i'm about to start the gasket replacement process. Thank's!
99 rodeo lse
|
|
Re: intake manifold torque specs 99 rodeo lse 3.2v6
[Re: trentch]
#856869
01/03/08 01:16 AM
|
Joined: May 2007
Posts: 36
Getting the Wheeling Fever
|
G'day, Yes, Isuzu manual says 18 lb-ft for all intake manifold bolts (near enough to your 17). 62Mb PDF workshop manual download for the V6 http://www.spottedhaggis.com/isuzu/090.pdfIt's for the Trooper but the engine/trans sections are applicable.
Last edited by boritz; 01/03/08 01:19 AM.
Aussie 1997 3.2V6 SOHC 6VD1 Holden Jackaroo SE (Isuzu Trooper/Bighorn/Monterey) 5-speed manual, rear LSD, front Lokka (manual free-wheel hubs).
|
|
Re: intake manifold torque specs 99 rodeo lse 3.2v6
[Re: boritz]
#856870
01/03/08 02:24 AM
|
Joined: Sep 2005
Posts: 416
Mudrunner
|
13 ft lbs. Isuzu revised it a while ago. There is a TSB about it but I dont remember which one at the moment. Make sure you use an inch lb wrench as a ft lb torque wrench wont be accurate enough at that low of a setting.
--Dave
1999 Rodeo LS 3.2 4x4 5 Speed 32x11.50-15 BFG T/A KO on US Wheel 94 series 3" Lift - Rancho 9000x Rear No-Slip Locker Flowmaster 50 series SUV 2.25"
There is a very fine line between "hobby" and "mental illness." - Dave Barry
|
|
Re: intake manifold torque specs 99 rodeo lse 3.2v6
[Re: Gizzy42]
#856871
01/03/08 02:43 AM
|
Joined: Apr 2000
Posts: 7,268
Isuzu Moderator
|
Make sure you use an inch lb wrench as a ft lb torque wrench wont be accurate enough at that low of a setting.
Just for clarification, what is it. lb-ft or lb-in?
13lb-ft is 156lb-in. I think most lb-in wrenches can do that, but low range lb-ft wrenches are out there too.
Just don't put 13lb-ft on a 13lb-in bolt. Actually, you won't get there. It will break long before you get that tight. <img src="/forums/images/graemlins/smile.gif" alt="" />
Good Luck, Michael
|
|
Re: intake manifold torque specs 99 rodeo lse 3.2v6
[Re: mlclark]
#856872
01/03/08 03:57 AM
|
Joined: Sep 2005
Posts: 416
Mudrunner
|
Its ft lbs. I always recommend converting to inch lbs and using an inch lb wrench at that low of a setting for accuracy and most ppl dont have low range ft lb wrenches.
--Dave
1999 Rodeo LS 3.2 4x4 5 Speed 32x11.50-15 BFG T/A KO on US Wheel 94 series 3" Lift - Rancho 9000x Rear No-Slip Locker Flowmaster 50 series SUV 2.25"
There is a very fine line between "hobby" and "mental illness." - Dave Barry
|
|
|
|
|
|
OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting.
Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.
PHP: 7.4.33 Page Time: 0.007s Queries: 15 (0.004s) Memory: 0.6071 MB (Peak: 0.6718 MB) Data Comp: Off Server Time: 2026-06-07 10:05:30 UTCValid HTML 5 and Valid CSS