|
|
 What transmissions take the 2.85 auto gears?
#886227
05/17/08 07:55 AM
|
Joined: May 2007
Posts: 435
OP
Mudrunner
|
I know they will fit the KM148 (AW372) and V4AW2, but will they fit the KM146 A/T on some of the early Gen1's?
1990 Monty LS 3.0 A/T LWB. KYB front shocks, OME rears and coils. 33x10.5 BFG Muds. 5.29, 2.85, RD110, RD46. 2 bouncys. Aisins. Monte Disco swaybar disconnects. GenII t-arms, idler arm, UCA's, V45W front brakes. 2in BL.
|
|
|
Re: What transmissions take the 2.85 auto gears?
[Re: DirtDriver]
#886228
05/17/08 04:15 PM
|
Joined: May 2007
Posts: 4,628
Roll Me Over
|
You're talkin t-case gears, right?
Fasteddy's advice is occasionally sound...
|
|
|
Re: What transmissions take the 2.85 auto gears?
[Re: DirtDriver]
#886229
05/17/08 04:32 PM
|
Joined: Jun 2003
Posts: 7,356
Trail Leader
|
The 2.85s are for the "smaller" t-cases. These are basically the GenIs and the earlier GenIIs. The GenII 3.5s and 24V 3.0s (MT only?) have a bigger case/gears inside that allowed them to be able to cut a set at 3.15.
There are different gears between engines and MTs and ATs. You need to be sure to cross-ref to the mitsu factory gear that you'll be replacing when you order a set from AU.
Big Truck: 00, 3.5, Endeavor, 5-Spd drive line in hand! Little Truck: 87, 2.6T I/C, MT, LSDs, Tonneau Top Her Truck: 03, 3.8, 20th Anniv, 65k Daughter's: 06 Eclipse, Keeping it Mitsu! FSMs: MitsubishiLinks.com
|
|
|
Re: What transmissions take the 2.85 auto gears?
[Re: hazy_daze]
#886230
05/17/08 07:42 PM
|
Joined: May 2007
Posts: 435
OP
Mudrunner
|
Yeah, I'm talking about the aussie t-case gears. I know absolutely they'll fit the V4AW2 which went in many 1990-1994 3.0 trucks. I'm almost positive they'll go in the KM148 that went in many of the Gen1's to 1989. But I don't have any idea if they'll fit in the KM146 which went in some of the earlier Gen1's. No biggie, I'm putting together installation instructions for the 2.85 t-case gears and I wanted to list the transmissions they'd go in.
1990 Monty LS 3.0 A/T LWB. KYB front shocks, OME rears and coils. 33x10.5 BFG Muds. 5.29, 2.85, RD110, RD46. 2 bouncys. Aisins. Monte Disco swaybar disconnects. GenII t-arms, idler arm, UCA's, V45W front brakes. 2in BL.
|
|
|
Re: What transmissions take the 2.85 auto gears?
[Re: DirtDriver]
#886231
05/17/08 11:05 PM
|
Joined: Jun 2003
Posts: 7,356
Trail Leader
|
I remember when DougH did his. He had 24V 3.0 and ended up needing the 3.15s. IIRC, that's when Mister Bishi made the general suggestion to order via the cross-ref to the stock gear. That way they wouldn't have to guess what was on what truck in various markets. (In Oz, they never had the 24V 3.0, which basically had the 3.5L tranny/tcase. So, they didn't know about this when Doug ordered his.)
Big Truck: 00, 3.5, Endeavor, 5-Spd drive line in hand! Little Truck: 87, 2.6T I/C, MT, LSDs, Tonneau Top Her Truck: 03, 3.8, 20th Anniv, 65k Daughter's: 06 Eclipse, Keeping it Mitsu! FSMs: MitsubishiLinks.com
|
|
|
|
