|
|
|
|
 Re: What I Did Instead of Going to Moab
[Re: Jim_Paget]
#945769
05/19/09 04:58 PM
|
Joined: Jun 2000
Posts: 3,702
Roll Me Over
|
Bummer Jim! We missed you...there were actually 3 other 1st gen Troopers there this year!
Steve Carlson - 95 Trooper LS expo rig
Serenity now!
|
|
|
Re: What I Did Instead of Going to Moab
[Re: BigSwede]
#945770
05/19/09 08:36 PM
|
Joined: Oct 2000
Posts: 394
Mudrunner
|
Pictures from the fun (mostly) at Walker Valley Walker Valley
'91 Trooper 3.4 V6, K&N, 33x12.5 Trxus MT's, Aisin hubs, 3" body lift, Rear ARB Naches Trail
|
|
|
Re: What I Did Instead of Going to Moab
[Re: Storm Trooper]
#945771
05/23/09 11:06 PM
|
Joined: Aug 2000
Posts: 4,868
OP
Roll Me Over
|
Well, I just found out what happened in the t-case. The needle bearing went south, in a big way. Since the hi-low slides on that bearing, it is pretty obvious why I could not get into 4-lo.
The clutch was really toasted, also. It was gone to the point that the pressure plat wasn't holding it against the flywheel. It was just sort of floating around in there.
|
|
|
Re: What I Did Instead of Going to Moab
[Re: Jim_Paget]
#945772
05/24/09 12:13 AM
|
Joined: Apr 2000
Posts: 7,268
Isuzu Moderator
|
Did you loose the ball bearing?
m
|
|
|
Re: What I Did Instead of Going to Moab
[Re: mlclark]
#945773
05/24/09 01:07 AM
|
Joined: Aug 2000
Posts: 4,868
OP
Roll Me Over
|
I haven't torn it down that far yet to find out.
|
|
|
Re: What I Did Instead of Going to Moab
[Re: Jim_Paget]
#945774
05/24/09 04:09 AM
|
Joined: Apr 2000
Posts: 7,268
Isuzu Moderator
|
What about the previous install-uninstall merry-go-round game you played? Did it make it back in where it was supposed to go? Or, you probably were not pulling the hi/lo cluster during those times.
Tis a bummer, though. I hope the mainshaft is ok. Does the cluster spin or is it welded to the shaft?
Michael
|
|
|
Re: What I Did Instead of Going to Moab
[Re: mlclark]
#945775
05/24/09 04:46 AM
|
Joined: Aug 2000
Posts: 4,868
OP
Roll Me Over
|
|
|
|
|
Re: What I Did Instead of Going to Moab
[Re: Jim_Paget]
#945776
05/24/09 06:00 AM
|
Joined: Apr 2000
Posts: 7,268
Isuzu Moderator
|
Oh, the suspense is killing me...
|
|
|
Re: What I Did Instead of Going to Moab
[Re: mlclark]
#945777
05/25/09 01:34 AM
|
Joined: Aug 2000
Posts: 4,868
OP
Roll Me Over
|
Well, the good news is that the needle bearing isn't welded in place. All the needles are in the bottom (since it is standing on the bellhousing) of the case. Things rattle around just fine. That is good news, I guess.
|
|
|
Re: What I Did Instead of Going to Moab
[Re: Jim_Paget]
#945778
05/27/09 11:20 PM
|
Joined: Apr 2000
Posts: 7,268
Isuzu Moderator
|
|
|
|
|
|
|
|
