|
|
 Fuso ring gear size = 9.5"=SR ring gears?
#988431
03/04/10 09:36 PM
|
Joined: Jan 2000
Posts: 16,227
OP
Web Wheeler
|
Bear with me and the following run-on / train of thought... Is what I've been hearing reading correct? The Gen 2 SR & Gen 2.5 Winter Package rear diff's ring gear is a 9.5" gear which is the same size as a Fuso Canter's ring gear and the Canter is sold as the FE model by Fuso USA and Fuso FE's may have come with a 5.29:1 gear ratio which therefore means there's a 5.29:1 ring & pinion available for my SR?!? <img src="/forums/images/graemlins/confused.gif" alt="" /> <img src="/forums/images/graemlins/zombie.gif" alt="" /> <img src="/forums/images/graemlins/cyclops.gif" alt="" /> TIA.
|
|
|
Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: off-roader]
#988432
03/04/10 10:12 PM
|
Joined: May 2007
Posts: 4,628
Roll Me Over
|
Yes. I've been searching for this for awhile now. They do exist. I haven't gotten a part number yet. My Mitsu parts guy has said that he'd pay for the J a p a n e s e ASA to order them for me and then cancel it. As it progresses, I'll update in this thread.
Fasteddy's advice is occasionally sound...
|
|
|
Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: off-roader]
#988433
03/04/10 10:17 PM
|
Joined: Jan 2009
Posts: 243
Wheeler
|
Bear with me and the following run-on / train of thought... Is what I've been hearing reading correct? The Gen 2 SR & Gen 2.5 Winter Package rear diff's ring gear is a 9.5" gear which is the same size as a Fuso Canter's ring gear and the Canter is sold as the FE model by Fuso USA and Fuso FE's may have come with a 5.29:1 gear ratio which therefore means there's a 5.29:1 ring & pinion available for my SR?!? <img src="/forums/images/graemlins/confused.gif" alt="" /> <img src="/forums/images/graemlins/zombie.gif" alt="" /> <img src="/forums/images/graemlins/cyclops.gif" alt="" /> TIA. Well Now i'm excited.... been a while since i have seen a fuso up close, and i didn't have a montero at the time but the axle does seem very similar all together. might even be the same third member. <img src="/forums/images/graemlins/notooth.gif" alt="" />
95 Montero SR- Stock
90 Turbo Miata - TD04 wrx turbo, Flyin miata suspension, Torsen diff, 225 RS3's
92 Mighty Max 4x4 - Retired
|
|
|
Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: hochkis]
#988434
03/04/10 10:55 PM
|
Joined: May 2007
Posts: 4,628
Roll Me Over
|
Fuso's in the US are too big. The Canter is a smaller version that was never offered here.
Fasteddy's advice is occasionally sound...
|
|
|
Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: hazy_daze]
#988435
03/05/10 12:59 AM
|
Joined: May 2001
Posts: 4,079
Roll Me Over
|
YOu'll be looking for the 2.8 diesel powered canter it uses the pajero drive train, misterbishi,toasty and i looked into this years back and what we found was 5.29's BUT the canter axle is FULL FLOAT and may have a different carrier than what we have. If you can find the Ring and pinion i'm sure if we just order 1 set and have a few of us pitch in on it then someone test fit it and if it doesn't fit no ones really out that much. I'll throw down some cash for it. Our fuso dealer was able to get it but we had to buy the whole 3rd member and it was $1000 so we passed.
89 2 dr turbo diesel
89/88 "Backwoods sas"
|
|
|
Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: lordtrunks]
#988436
03/05/10 01:17 AM
|
Joined: Jan 2000
Posts: 16,227
OP
Web Wheeler
|
YOu'll be looking for the 2.8 diesel powered canter it uses the pajero drive train, misterbishi,toasty and i looked into this years back and what we found was 5.29's BUT the canter axle is FULL FLOAT and may have a different carrier than what we have. If you can find the Ring and pinion i'm sure if we just order 1 set and have a few of us pitch in on it then someone test fit it and if it doesn't fit no ones really out that much. I'll throw down some cash for it. Our fuso dealer was able to get it but we had to buy the whole 3rd member and it was $1000 so we passed. Can your fuso dealer pull up the part number for just the ring/pinion gear? I might have a source via the Philippines. I recently learned that some of my cousins drive or used to drive Pajero's there. <img src="/forums/images/graemlins/cyclops.gif" alt="" />
|
|
|
Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: off-roader]
#988437
03/05/10 02:03 AM
|
Joined: Jan 2000
Posts: 7,309
Trail Leader
|
Interesting stuff. My 490s work for my truck, but for those with 460s it would be a big upgrade on bigger than stock tires.
Ray, where are your revs sitting at on the highway, in OD, at say, 60mpg, on 35s?
|
|
|
Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: PHIL_]
#988438
03/05/10 03:45 AM
|
Joined: Aug 2008
Posts: 1,186
Body Damage is Cool
|
what about the front? or are they 4wd?
'88 Raider, 33" Maxxis, 2" body lift, 10K winch
|
|
 Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: PHIL_]
#988439
03/05/10 03:56 AM
|
Joined: Dec 2000
Posts: 6,896
Trail Leader
|
Ray, where are your revs sitting at on the highway, in OD, at say, 60mpg, on 35s?
The H and the G make a huge difference. We know what you mean.
Last edited by sparkem; 03/05/10 03:57 AM.
I just want to tell you both good luck, and we're all counting on you.
|
|
|
Re: Fuso ring gear size = 9.5"=SR ring gears?
[Re: 0778drz110]
#988440
03/05/10 03:58 AM
|
Joined: May 2001
Posts: 4,079
Roll Me Over
|
No part number he called a different country I can't remember which and they had one, you see Fuso dealers are also junkyards so you can buy new and used parts from them, have your friends ask about a used set as well ray. As far as the front canter axle i don't what it uses I know its solid and could be a front version of the 9.5 but it will also be full float.
89 2 dr turbo diesel
89/88 "Backwoods sas"
|
|
|
|
