|
|
1990 4Runner info
#989504
03/12/10 03:30 AM
|
Joined: Sep 2004
Posts: 270
OP
Mudrunner
|
I have a buddy that will be joining the forum soon, he has just obtained a 4Runner that is bone stock, rebuilt V6. Needs to know the bolt on mods, exhaust, intake, etc. to get the most out of it without sacrificing reliability, or driveability. Any words of wisdom? I have a pickup so normally see everything in the early trucks forum, but I like this one as well. Thanks.
|
|
Re: 1990 4Runner info
[Re: xrtim]
#989505
03/12/10 04:43 AM
|
Joined: Jan 2001
Posts: 11,595
Forum Moderator
|
Words of wisdom? Save your money. For what you spend on those mods, you wont get much improvement.
Spend the money on maintenance and upkeep on the rig.
Just get a decent cat back exhaust and high flow air filter and live live with it. If the engine is properly maintained it will run a hundred times better than a poorly maintained engine.
Also, make sure you have the proper axle gears for the size tire your running. 4.10's for 31's, 4.88's for 32's, and 5.29's for 33-35".
|
|
Re: 1990 4Runner info
[Re: Adam F]
#989506
03/12/10 12:32 PM
|
Joined: Apr 2000
Posts: 4,282
Roll Me Over
|
Words of wisdom? Save your money. For what you spend on those mods, you wont get much improvement.
Spend the money on maintenance and upkeep on the rig.
Just get a decent cat back exhaust and high flow air filter and live live with it. If the engine is properly maintained it will run a hundred times better than a poorly maintained engine.
Also, make sure you have the proper axle gears for the size tire your running. 4.10's for 31's, 4.88's for 32's, and 5.29's for 33-35". ^^^^^^ this...
leo d. 90 4runner, v6, auto, WCOR CitB kit, marlin duals, arb rear, tt front 4.88, blah, blah, blah... Pres. of TEAM IFS! and GETTING OFF 4WD Club member
|
|
Re: 1990 4Runner info
[Re: Adam F]
#989507
03/15/10 03:39 AM
|
Joined: Sep 2004
Posts: 270
OP
Mudrunner
|
That is pretty much what he plans on doing but doesn't know the details about what brands, size of exhaust from the cat back, etc. I advised him to leave it as alone as possible, but intake/exhaust, and gearing are pretty much required to make a decent runner. Thanks for the response.
|
|
Re: 1990 4Runner info
[Re: xrtim]
#989508
03/15/10 05:10 AM
|
Joined: Jan 2001
Posts: 11,595
Forum Moderator
|
2.25" from cat back. Any decent muffler (vortex, flowmaster, borla) should be OK.
|
|
Re: 1990 4Runner info
[Re: Adam F]
#989509
03/18/10 04:49 AM
|
Joined: Sep 2004
Posts: 270
OP
Mudrunner
|
Did that with a flowmaster, gonna get a K & N intake next. Any body lift needed to go to 35 inch tires?
|
|
Re: 1990 4Runner info
[Re: xrtim]
#989510
03/21/10 03:02 PM
|
Joined: Jan 2001
Posts: 11,595
Forum Moderator
|
What suspension setup? You'd need probably at least 4" of lift to get 35's to clear, or a lot of body triming. And 5.29 gears.
|
|
|
|